Technical
specifications:

* Water ORP (oxidation-reduction potential) depends on factors such as mineralization and flow rate. Changes in these factors can affect the ORP level. A high flow rate and low mineralization can affect water parameters. Therefore, in order to achieve the desired ionization results, it is necessary to take these variables into account.

** Water pH can also vary depending on the mineralization and initial flow rate. Proper pH regulation requires taking these factors into account. A high flow rate and low mineralization can produce different pH levels than a low flow rate and high mineralization. Thus, ionization regulation needs to take these variables into account.

Prepared water MODES:
.5 PH – For disinfection 5.5 PH - For plants 6.5 PH - For beauty 8.8 PH - For drinking 11.0 PH - For food

*Note: Slight errors may occur for all pH values, which may be caused by water flow and water salinity fluctuations. To ensure an accurate pH level, these factors must be properly regulated and controlled.

Expected flow rate of tap and prepared water:

Tap water – 4.5-7.6 L/min.

Filtered water – 1.4-1.7 L/min.

Alkaline water (8.8-11.0ph) – 0.8-1.2 L/min.

Acidic water (3.5-6.5ph) – 0.4-0.7 L/min.

*Note: It is mandatory to ensure that the water inlet meets the minimum requirements: 5.6 l/min at a pressure of 150–500 kPa (1.5–5 Bar). Only in this case can the declared results be expected.
Installation:
When installing the Respo device, the following technical requirements must be observed to ensure proper system operation and operational safety:
Mixer mounting hole size:
◊ Minimum diameter: 40 mm.
◊ Maximum diameter: 44 mm.
◊ Maximum distance from the hole in the countertop to the cold and hot water inlets: 550 mm.
◊ Inlet standards: 1/2" and 3/8".
Mixer mounting hole size:
◊ Minimum diameter: 40 mm.
◊ Maximum diameter: 44 mm.
◊ Maximum distance from the hole in the countertop to the cold and hot water inlets: 550 mm.
◊ Inlet standards: 1/2" and 3/8".
Mixer mounting hole size:
◊ Minimum diameter: 40 mm.
Mixer mounting hole size:
◊ Minimum diameter: 40 mm.
◊ Maximum diameter: 44 mm.
◊ Maximum distance from the hole in the countertop to the cold and hot water inlets: 550 mm.
◊ Inlet standards: 1/2" and 3/8".
Mixer mounting hole size:
◊ Minimum diameter: 40 mm.
◊ Maximum diameter: 44 mm.
Mixer mounting hole size:
◊ Minimum diameter: 40 mm.
◊ Maximum diameter: 44 mm.
◊ Maximum distance from the hole in the countertop to the cold and hot water inlets: 550 mm.
◊ Inlet standards: 1/2" and 3/8".
mportant: Failure to comply with these requirements may cause installation and operation problems. Installation video and drawing are attached.
Service

PP/GAC Filter - PP/GAC must be replaced every 180 days (6 months) from the first use. This is necessary to ensure the hygienic properties of the device, optimal operation and the best water quality. The time to filter replacement is calculated automatically, and when the day comes to replace the filter, a corresponding message will appear on the LCD screen. These indicators can also be checked in the LCD Menu: Settings → Time to service → to filter replacement/to washing, or monitored in the official Respo Water mobile application. Failure to replace the filter in time may negatively affect the functionality of the device. https://youtu.be/-6HbCxFB7Po

Mineral cartridge - the mineral resource is tracked by the device and the official Respo Water mobile application, which automatically monitors the use of the cartridge in percentages – from 0% to 100%, corresponding to approximately 300 liters of mineralized water. When it is time to replace the mineral cartridge, a notification will be displayed in both the mobile application and the LCD screen. This mode is indicated by the mineral icon in the LCD screen (top right). If there is no icon, the mode is not active. The cartridge resource can be checked in the mobile application. Failure to replace the mineral cartridge in time may only affect the water quality. https://youtu.be/TnXizkYvjO8

Washing - The Respo device automatically calculates water consumption in minutes and evaluates the level of scale formation in the system. After reaching the consumption limit of 240 minutes, the device suggests washing. If washing is not performed several times in a row, Respo will not allow the production of ionized water in order to protect the system from possible damage. The washing status and time to washing can be checked in the LCD Menu: Settings → Time to service → to filter replacement/to washing, as well as in the official Respo Water mobile application. Failure to comply with or ignoring this function may result in loss of warranty. This function ensures the durability and efficiency of the device. https://youtu.be/YCZpyW-56c0

Mobile
application

The “Respo Water” official mobile application is an essential tool both in the initial setup of the device and in its daily maintenance and management. It allows:

01
Initial setup and connection to the network:

The application is necessary for device registration and connection to the Internet network. Once connected, the device automatically transmits data to the “Respo” server, where it is processed, providing the user with personalized insights into the device’s condition and operation.

02
Initial setup and connection to the network:

The application is necessary for device registration and connection to the Internet network. Once connected, the device automatically transmits data to the “Respo” server, where it is processed, providing the user with personalized insights into the device’s condition and operation.

03
Initial setup and connection to the network:

The application is necessary for device registration and connection to the Internet network. Once connected, the device automatically transmits data to the “Respo” server, where it is processed, providing the user with personalized insights into the device’s condition and operation.

04
Initial setup and connection to the network:

The application is necessary for device registration and connection to the Internet network. Once connected, the device automatically transmits data to the “Respo” server, where it is processed, providing the user with personalized insights into the device’s condition and operation.

Warranty
and after-
sales service
01 Warranty conditions

UAB “Burbuliukas ir CO” warrants to the original purchaser that the “Aquator Respo” product is free from manufacturing defects and material defects, and undertakes, at its discretion, to repair or replace the defective product or part thereof free of charge during the warranty period. The warranty period is valid for 5 (five) years from the date of purchase.

◊ Any cosmetic damage to the product, flexible pipes, hoses, accessories, printed material.

◊ Damage caused by improper voltage or improper use, misuse of the product.

◊ Product modifications that were made without the manufacturer's consent.

◊ Damage caused by natural disasters or other unforeseen events.
◊ When using third-party filtering systems, the warranty is no longer valid.

Electrode reactor maintenance

Electrode reactor maintenance must be performed after each notification that appears on the LCD screen. The system automatically evaluates the condition of the reactor and performs washes. The user only needs to perform maintenance using a special cleaning agent designed for effective reactor maintenance.

03 Warranty service procedure

To use the warranty, contact Homeovita SRL, provide the product purchase documents and describe the problem. The customer service team will provide information on how to submit the product for repair or replacement.

Warranty service contacts:

Address: Homeovita SRL, Zavodskaia str, 2

Phone: +373 69107422

02 Warranty service restrictions
This warranty does not apply to the following cases: THIS LIMITED WARRANTY APPLIES ONLY TO DEVICES PURCHASED AND INTENDED FOR USE IN THE COUNTRY OF PURCHASE. The warranty does not apply to damage incurred outside the country (e.g., due to improper voltage or an unsafe water source). Warranty cancellation applies in the following cases:

◊ If the product was repaired by unauthorized representatives.

◊ If unauthorized product modification or damage was performed.

04 Additional informatioN

◊ The warranty is non-transferable without the express permission of the manufacturer..

◊ Ensure that you have the product serial number when contacting for service.

◊ It is recommended to clean and maintain the product in accordance with the instructions for use to avoid possible defects.

Electrode reactor maintenance

Electrode reactor maintenance must be performed after each notification that appears on the LCD screen. The system automatically evaluates the condition of the reactor and performs washes. The user only needs to perform maintenance using a special cleaning agent designed for effective reactor maintenance.

The manufacturer and seller ensure that all warranty services will be performed to the highest standards to ensure customer satisfaction and long-term use of the product.